Select First Picture
This affects the contrast of the picture you're currently editing.
Contrast Level:
This affects the brightness of the picture you're currentlyediting.
Brightness Level:
This is the inner diameter of the sphere. The maximum outer diameter of thesphere would be this plus 2 times the maximum thickness.
SphereDiameter (mm):
This determines whether or not there is a holeand cylinder at the bottom of the sphere.
Optional Cylinder on Bottom
This is the outer diameter of the cylinder below the sphere, if you have one.
Cylinder Outer Diameter (mm):
This is the height of the cylinder, which is the distance between the base of thesphere and the bottom of the cylinder.
CylinderHeight (mm):
This is the thickness of the cylinder and the ledge at the bottom of thecylinder.
CylinderThickness (mm):
This is the outer diameter of the ledge at the bottom of the cylinder.
Ledge Outer Diameter (mm):
This determines whether or not there is a holeat the top of the sphere.
Optional hole at the top
This determines the distance between pictures on the lithophane surface.
Top HoleDiameter (mm):
This is the distance between unique thicknesses on your lithophane stl. A smallvalue makes your lithophane have a finer resolution, but also makes the stl filemuch larger.
LithophaneResolution (mm/px):
This is the vertical angle on the sphere that the picture is projected onto.
Picture Height (degrees):
This is the horizontal angle on the sphere that the picture is projected onto.
PictureWidth (degrees):
This is the maximum thickness of the lithophane surface. The correct value heredepends upon the filament that you're using.
MaxThickness (mm):
This is the maximum thickness of the lithophane surface. The correct value heredepends upon the filament that you're using, and it shouldn't be less than 1.5xyour nozzle's diameter.
MinThickness (mm):
This determines whether or not there is a holeand cylinder at the bottom of the sphere.
Lithophane Options
This is the distance from the bottom left corner to bottom right corner.
Width (mm):
This is the distance between the build plate and the topmost point of thelithophane.
Height (mm):
This is distance between the front of the frame and the back of the frame.
Frame Depth (mm):
This is distance between the buildplate and the base of the lithophane image
Frame Height(mm):
This determines the overhang angle on the frame.
Overhang Angle(degrees):
This is the thickness of the stand.
StandThickness (mm):
This is the angle of the stand's legs.
Stand Angle(degrees):
This is the distance between unique thicknesses on your lithophane stl. A smallvalue makes your lithophane have a finer resolution, but also makes the stl filemuch larger.
LithophaneResolution (mm/px):
This is the maximum thickness of the lithophane surface. The correct value heredepends upon the filament that you're using.
MaxThickness (mm):
This is the maximum thickness of the lithophane surface. The correct value heredepends upon the filament that you're using, and it shouldn't be less than 1.5xyour nozzle's diameter.
MinThickness (mm):
This is the distance from the bottom left corner to bottom right corner.
Width (mm):
This is the distance between the build plate and the topmost point of thelithophane.
Height (mm):
A higher value makes the lithophane more curved. A small curvature makesthe lithophane flatter.
Curvature [0-1]:
This is distance between the front of the frame and the back of the frame.
Frame Width (mm):
This distance is how far you will slide your night light lithophane onto thenight light.
Slot Depth (mm):
This is the width of the slot that goes around the diameter of the night lightfixture.
Slot Width (mm):
This is the thickness of the base that needs to slide into your night light'sslot.
Thickness of Base(mm):
This is the ditstance between the night light's light and the lithophane.
LightDistance (mm):
This is the distance between unique thicknesses on your lithophane stl. A smallvalue makes your lithophane have a finer resolution, but also makes the stl filemuch larger.
Lithophane Resolution(mm/px):
This is the maximum thickness of the lithophane surface. The correct value heredepends upon the filament that you're using.
MaxThickness (mm):
This is the maximum thickness of the lithophane surface. The correct value heredepends upon the filament that you're using, and it shouldn't be less than 1.5xyour nozzle's diameter.
MinThickness (mm):
This is the height of the lithophane lamp. Your printer's build volume must betaller than this for you to print the lamp.
Height (mm):
This is the top diameter of the lithophane lamp.
Top Diameter(mm):
This is the bottom diameter of the lithophane lamp.
Bottom Diameter(mm):
This is the number of waves on the lithophane lamp's profile.
Number of waves:
This is the height of waves on the lithophane lamp's profile.
Height of thewaves (mm):
This determines the size of the frame at the top and the bottom of the lamp.
Base Width andHeight (mm):
This determines the overhang angle on the frame.
Overhang Angle(degrees):
This is the distance between unique thicknesses on your lithophane stl. A smallvalue makes your lithophane have a finer resolution, but also makes the stl filemuch larger.
LithophaneResolution (mm/px):
This is the maximum thickness of the lithophane surface. The correct value heredepends upon the filament that you're using.
Maximum Thickness (mm):
This is the maximum thickness of the lithophane surface. The correct value heredepends upon the filament that you're using, and it shouldn't be less than 1.5xyour nozzle's diameter.
Minimum Thickness (mm):
This determines the distance between pictures on the lithophane surface.
Gap BetweenPictures (mm):
This determines the thickness of the spacing between pictures. A zero makes thespacing the maximum thickness (min brightness), and a 1 makes makes the spacingthe minimum thickness (max brightness).
GapBrightness (0-1):
This determines whether you have a clamp or aledge as the interface to your lamp.
Frame Options
This determines the inner diameter of the ledge.
Ledge Diameter(mm):
This determines height of the cylinder.
Cylinder Height(mm):
This determines the inner diameter of the cylinder.
CylinderDiameter (mm):
This determines the thickness of the cylinder and ledge.
Cylinder Thickness (mm):
This determines height of the spokes.
Spoke Width(mm):
This determines the width of the spokes.
Spoke Height(mm):
Use this to add or remove a hole from the top ofthe heart that can be used to hang it or put it on a keyring.
Hole
This is the distance from the left-most edge of the heart's frame to theright-most edge of the heart's frame.
Width (mm):
This is the distance between the top-most edge of the heart model to thebottom-most edge of the heart model.
Height (mm):
This is distance between the front of the frame and the back of the frame.
Frame Size (mm):
A higher value makes the base as flat as possible, and a lower value makes thebase as curved as possible.
Base Flatness(mm):
This determines whether or not there is aninterface to a light source at the base of the heart lithophane.
Light Fixture
This is the thickness of the stand.
StandThickness (mm):
This is the diameter of the clamping feature.
Clamp InnerDiameter (mm):
This is the thickness of the clamping feature.
ClampThickness (mm):
This is the distance between the lithophane and the center of the clampingfeature (which likely holds your light source).
Light Distance(mm):
This is the distance between unique thicknesses on your lithophane stl. A smallvalue makes your lithophane have a finer resolution, but also makes the stl filemuch larger.
Lith Resolution(mm/px):
This is the maximum thickness of the lithophane surface. The correct value heredepends upon the filament that you're using.
MaxThickness (mm):
This is the minimum thickness of the lithophane surface. The correct value heredepends upon the filament that you're using, and it shouldn't be less than 1.5xyour nozzle's diameter.
MinThickness (mm):
Your Image
Your Cropped Image at Resolution
Rendering Resolution (mm/px):
A large value will reduce rendering time, but too large of a value could eventually causeerrors. A small value will show you the details of your lithophane's image.